Electronics

Description:  Material: red copper Wiring Square: 0.08-4mm Rated current: 32A Hole position: 8 in 8 out Package included: 20 x Terminal Block..

Description:Specification: potentiometerType: Single-line typeFeatures: RollerShaft diameter: 6mmInstallation thread diameter: 7 mmBase size: 16*7mmKnob size: 15*17mmTotal length: 25mmPackage Included:4 x B5K4 x B10..

Specification: Model: SS-12D00G3Type: 1 Pole 2 ThrowTerminal Quantity: 3pcsWorking Power : 0.5A 50V DCContact Resistance: 30mΩ MaxInsulation Resistance: 100mΩ Min at 500V DCWithstand Voltage: AC 500V for 1 minTerminal Length: 3mm/ 0.12"Pin Pitch..

20T GT2 Aluminium Timing Pulley 2GT 5M Belt For RepRap Prusa Mendel 3D PrinterGT2 Pulley:   Teeth witch: 2mm Teeth number: 20 width: 6mm Teeth width: 7mm (Very Suitable and good for 6mm synchronous belt) Diameter of bore: 8mm Flange: Double Material: Aluminium Setscrews: M4GT2 Belt:Pitch: 2mm ..

Introduction: Post-curing lamp for 3D printer. Say goodbye to several kilowatts of power consumption, farewell to several hundred degrees of high temperature, farewell to hundreds of hours or even tens of hours of life, farewell to several minutes of warm-up time. About curing effect: To..

Features : - Outdoor IP Camera - 2.0MP high definition video recording - Connection to phone or tablet through 2.4G Wifi - Remotely view on the phone or table screen - Two way voice communication - Infrared LEDs and white LEDs offer colorful night vision - Support TF c..

Parameter:Working voltage: 5V power supplyOverall dimension: 25cm * 3.6cmShell size: 9.5cm * 7.5cm * 5.5cmCircuit board material: double sided 1.6mm Rf-4 boardDescription:- Three spectrum modes:1. The spectrum is pushing and inching2. Single spectrum3. Single inching- Press to switch mode:The lamp i..

Features: Made of wood and magnet material, safe, non-toxic and durablePerfect for posters, prints, photos, fabric, even canvasEasy to roll up or hanging on the wall through the doubled-sided adhesive tape, but the rope is not included in package listingIt is a valuable gift or fa..

Features: 1. Power module for controlling 3D printer heated bed 2. Handle high current but without being heat at the same time 3. Powerful MOSFET HA210NO6 4. Allow PID control of the heated bed (DC-DC Relays usually do not allow this) 5. Safe for prolonged times without active cooling. 6. Ca..

Features:Lightweight, easy storage and carryFor photography, parties, bars, etcColor fidelity, Satisfied effectUsing a series of high-tech digital production equipment, the picture is clear, realisticMaterial: Cloth (vinyl)Color: White + greenPattern: Pink FlowerSize: 210x150cm (7ftx5ft) / 150x90cm ..

Remove Crease:   In order to facilitate transport and packaging, items sent folded, resulting in the crease. The recovery methods as following: Roll it up tightly with a cylinder and then just waiting for 2 to 4 days. The wrinkles and crease are almost removed. If necessary, you can iron the..

Specification:Material: copper+plastic Surface: tin-Plated Type: 6 Value Box Size: approx. 195*130*35mm Size: about 0.5mm2;---16mm2; (22AWG-5AWG) Color: Blue, Green, Yellow, Red, White, Black, Orange Quantity: 2120pcs E0508 22AWG 0.5mm2; (Orange) X 200pcs E0508 22AWG 0.5mm2; (White) X 200pcs E1008..