DIY Electronic Kits

Specification:Product: SM 2.54mm Male Plug Housing and Female Socket Housing With Metal Terminals ConnectorMaterial: Plastic+MetalColor: BlackPins: 2P, 3P, 4P, 5PinPitch: 2.54mmBox Size: Approx 130 x 66 x 22mm (L*W*H)Used for household appliances, LED lighting, computers, electronic toys, batteries,..

Specification:Certifications: TUV CEDielectric Strength: 1,500V (minimum)Insulation Resistance: 100Megohms(minimum)Base Material: Nylon66Actuator Material: Nylon66 or PCTerminal Material: H62CuFeatures:1. Designed to connect and disconnect an DC12V 20A electrical circuit at will,SPST:ON-OFF control...

Parameter:Working voltage: 5V power supplyOverall dimension: 25cm * 3.6cmShell size: 9.5cm * 7.5cm * 5.5cmCircuit board material: double sided 1.6mm Rf-4 boardDescription:- Three spectrum modes:1. The spectrum is pushing and inching2. Single spectrum3. Single inching- Press to switch mode:The lamp i..

Introduction:The Raspberry Pi Pico 24 in 1 sensor kit mainly contains 24 commonly used sensors, modules, a Raspberry Pi Pico board, a Raspberry Pi Pico expansion board and Dupont wires.The 24 sensors and modules are fully compatible with the Raspberry Pi Pico shield. You only need to stack the Raspb..

Introduction:The Raspberry Pi Pico 24 in 1 sensor kit mainly contains 24 commonly used sensors, modules, a Raspberry Pi Pico board, a Raspberry Pi Pico expansion board and Dupont wires.The 24 sensors and modules are fully compatible with the Raspberry Pi Pico shield. You only need to stack the Raspb..

Feature:Plastic bag package only. 24 in 1 sensor kit for  UN0 R3, this kit includes temperature sensors, rotary encoders, high sensitivity microphones commonly used in study, each module has a good weld, can be directly connected to form a system in the control board, make some interactive works. ..

Description:Type 1: 37 sensor kits:1 x Infrared sensor receiver module1 x head sensor module1 x Temperature and humidity sensor module1 x Infrared emission sensor module1 x 5V relay module1 x For arduino finger detect heartbeat module1 x Microphone sensitivity sensor module1 * Metal touch sensor mo..

Description: It does not require programming or a microcontroller, so please do not provide the code.It does not provide power, you can use the charging treasure (5V DC) as the power supply, or use 4pcs AA battery box and load 4 batteries. About each part of the test:  1. Test ..

Description:It is DIY kit, need to assemble yourself. Power supply: 2 x CR927 button batteries(Not included) Finished Size: 81*30*20mmPackage included:3 x DIY Electronic POV Rotate Fingertip Gyro Soldering Kit..

Description:Working voltage: 3~12V Board size: 90 x 60 x 1.6mm This DIY SMD practice board suitable to improve soldering level and speed. Package included: 3 x SMD Components Soldering Skill Training Kit..

Description: MB-102 830 Point Solderless PCB Breadboard: Quantity: 3 Pcs Model: MB-102 Dimension: 16.7 x 5.7 x 1cm Tie Points: 830 tie points (consists of: 630 tie-point terminal strip, 200 tie-point distribution strips) Matrix: 126 separate 5 point terminals, plus 4 horizontal bus lines (..

Features:1. The AKE-1 kit uses PAM8403 as the power amplifier chip. PAM8403 is a Class D audio power amplifier, which can provide 3W power with an efficiency higher than 85%, and has the characteristics of high efficiency, high power, and low distortion.2. A good horse is equipped with a good saddle..